professional manufacturer fully automatic aerosol filling machine for aerosol generator   As a professional manufacturer in china.We can supply you the total Aerosol related machine (chemicals storage tank,mixing machine,filling machine,shrink packing machine) . And also can supply accessory(aerosol spray cans ,aerosol vlaves ,plastic cover,  glass bead etc.)   Aerosol filling machine description:   1)Can Arranging Machine Famous in providing efficient and accurate performance. It can bottle the “horse mouth” metal can with the international standard of 1 inch diameter and aluminum type spray bottle. 2)Valve Inserting Machine can choose valves automatically, the valves will be sent to producing line from the pipe productivity. Under the air power, putting the valves and press them on the can tightly. Good capping quality ,it saves labors and increase the working efficiency. Select for direction by rotary disk, then pipe consistency conveyor and regularly places into tank inlet, accordingly instead manual operation and reduces labor cost. Power for rotary disk: AC380C 0.37KW Production capacity :40 cans/minutes Available valve: 1”(25.4mm) 3)Crimping and Propellants filling machine mainly fill the gases into cans, such as LPG, DME, Butane gas ,propane gas ,Carbon dioxide, Nitrogen, compressed air, etc. The propellants filling machine set consists of four stations:   A .The correcting device of aerosol valves. When workers operating valves, due to incorrect disposal of valves, press valves outside the can opening, or longish valve suckers, the valves will jump out of the can opening and away from the Centre. At the moment, the correcting device of aerosol valves can correct valves, aim at and press into can opening. Since there are three points under the valves, although the sucker is long, the valve will never jump out of cans again. It is easy to continue to seal.   B. Crimping device: The crimping head is mainly used to seal on the corrected and pressed valve with internal expanding mode. It needs to finish two steps respectively. Firstly, the pressure cylinder presses valves on the opening to make the valve rubber gasket flatten against the opening,usually the compression is 0.2-0.3mm.Then, the pressure cylinder sends a signal to inform sealing cylinder to operate. The capper is fast, reliable, steady and easy to adjust sealed diameter and sealed depth manually without any tool.   C .Four propellants filling stations: These three filling stations are composed by three independent filling machines. The maximum inflation amount is 200ML and 800ML in total. According to 750ML aerosol can, in general, it will not exceed 400ML if fill LPG. Therefore, the 400ML capacity can far meet the filling demands of aerosol products. The measuring cylinder of inflator is made of 304 stainless steel materials. The processing techniques and precision are the same as the measuring cylinder of filling liquid machine. The seal rings of inflator adopt CFRP skeleton rings of tetrafluoroethylene produced by American, which located in U-groove with stainless steel reeds inside. When seal rings are normally worn in long-term operation, the outer diameter of seal rings will automatically compensate due to the function of reeds.   D.The propellant booster pump: CJXH-2800A full-automatic butane gas filling machine is equipped with two high-capacity booster pumps. The Max pressure of booster bump is up to 3.0Mpa. It has high delivery speed and reliable & steady performance. In addition, we specially set up a high-pressure and buffer fluid reservoir, which is used to reserve the pressurized 1.0 Mpa propellants. (In general, LPG,DME,F12 can be pressurized to 1.2Mpa and become liquid. In this way, it can ensure the three measuring cylinder of filling machines have stable operating pressure and sufficient supply, so as to fill rapidly and measure accurately.   4)Automatic aerosol water bath leakage testing machine can used dor testing all kinds of aerosols and gas without limit of can materials. The testing efficiency is 50-70 cans per minute and the products can be 100% tested. The explosion-proof motor equipped with automatic overload separator is used as the main driving device and therefore ensures safe operation of the complete machine. In the water lank is installed a flameproof electric heater which can heat the water to the temperature required and control the temperature automatically. Temperature control Accuracy:±1℃ power of Main Drive Devicc(Kw):0.75KW Water Tank Capacity:1.2M3 Water-Heating Power :36KW Drying Air Pressure:0.3-0.6Mpa Control Cabinet and Heater Type:explosion-proof Max.Air Consumption:0.6M3/min Product picture for your reference:       Any more details,pls contact me.